48v 60v 72v Power 500w 800w 1000w 1500w 1600w 2000w 3000w 3500w Ebike Motor Controller 45A 50A With LCD Display The special of sinewave controller compared to square wave controller 1. Silent,no noise 2. Sine wave controllers use high-frequency PWM frequency conversion technology to control the speed and current of the motor, It maks the load of the motor more balanced, thereby improving output power efficiency and reducing energy loss. Thus extending the battery life. 3. Sinewave controller can more accurately control the speed and current of the motor thereby improving power performance. It doing accelerating faster and bringing a more comfortable smooth driving experience. The special of this controller: 1. Controller with 5 hall sensor wire and it could work with motor without 5 hall sensor. 2 accelerator method. Accelerator from lcd display or add new accelerator on controller with standby accelerator. When you add extra accelerator, the accelerator on lcd dsiplay will not work. What's the difference of the choice? Each choice is inclued 1 piece controller+1 piece colorful lcd dsiplay +1 piece wire box 36v48v500w-1200w30A, 9MOS, Max current 30A,wide voltage design 36v 48v 60V , suitable for motor 36v500w 800w 48v 500w 800w 1000w 1200w, controller size 11*7.0*3.8cm 48V60V1000W-15000W,9MOS, Max current 30A,wide voltage design 36v 48v 60V , suitable for motor 48V 60V 1000w 1200w 1500W, controller size 11*7.0*3.8cm 48v60v1500w-2000w45A, 1 2 MOS， Max current 45A, wide voltage design 48v 60v 72V, suitable for motor 48v 1500w 60v 1600 2000w, controller size 12.5*7.0*3.8cm 60v72v2000w-3500w50A， 12 MOS， Max current 50A,wide voltage design 48V 60v 72v , suitable for motor 60v 2000w 60v 2600w 3000w 72v 3000w 3500w, controller size 12.5*7.0*3.8cm LCD display wire length 183cm Controller 48v /60v/72v 2000w-3500w, 12MOS, Max current 50A Wire data A. Battery wire B. Motor Hall sensor wire C. Motor phase wire D. Lcd display E. Auto-learn wire 1. Power lock (keep it short connected if there is no power lock key in your scooter) 2. Parallel power wire for dual drive （accelerator signal） 3. Reverse 4. Light 5.Brake light 6. Brake (low level and there is 2 connector) 7. Speed limited (eco/turbo,speed close to 25km/h) 8. Standby accelerator (when lcd display fault, it could be used by build new power in wire) Test Procedure 1. Please rack up your bicycle and do the unload test. Please connect battery, 3 phase wire, 5 hall sensor wire, LCD display and battery. Please ensure each wire was connected tie and no loosen. 2. Turn on the LCD display, set voltage of the LCD display in battery voltage , 48v 60v or 72v. Please also set other data on LCD display , pole pairs, wheel size. 3. Keep LCD display on and Connect the auto-learn wire on each side. NOTE !!! Motor will run itself without touching accelerator. It will stop running when you press the accelerator on LCD display or depart the auto-learn wire. Depart each side auto-learn wire when the motor run well, auto-learn wire only was used for motor test. 4. When wheel run well and smooth, you can start test with other function wire with accessories on your scooter Wire from LCD display Red (vcc) Lcd display power wire Blue(K) Controller power wire BLack(GND) LCD display GND wire Green (RX) LCD display data receiving wire Yellow (TX) LCD display data sending wire LCD display data setting, Long press power key and mode key into setting page. Power key for page change and mode key for data change (only P3 P06 P07 needs to be set) keep P9 IN 0, P10 in 1 P01 Lightness, 1 is dark and 3 is lightest P02 Mileage km or mph P03 Voltage setting 36v-72v P04 Sleeping time, 0 is none and other data is 1-60 minutes P05 Assistant level 0-3 ( Useless) P06 Wheel size inch in 0.1inch P07 Magnet pcs P08 Speed limited 0-100km/h, 100 means no speed limited (no limited) P09 Zero start 0 or non-zero start 1(keep it in 0) P10 Drive mode 1 electric drive 2. PAS drive (keep it in 1 electric drive since there is no PAS sensor from this controller) P11:PAS none (useless) P12 Start hardness, from 0-5 P13 PAS setting (NONE, IT CAN’T BE REALIZED SINCE THERE IS NO PAS WIRE FORM CONTROLLER) P14 Controller current Limited set (it can't be set, the min current limit is 20A) P15 Controller voltage short setting 48v is42, 60v is 54v,72v is .66 P16 None P17 Cruise, 0 is no cruise, 1 is yes P18 ABS brake hardness, 0-3, soft to hard (not work, it is low brake design) Error Code or Driving situation 0 Normal 1 Stay 2 Brake fault 3 None 4 6km/h 5 Cruise 6 Battery Voltage Short 7 Motor fault 8 Accelerator fault 9 Controller fault 10 Lcd display receiving fault 11 Lcd display sending fault 12 BMS communication fault 13 Front light fault lcd display show Error fault

مواصفات المنتج