BIGTREETECH Octopus V1.1 Motherboard 32Bit Control Board TMC2209 TMC5160T 3D Printer Parts VS SKR V1.4 Turbo For Voron 2.4 CR10

٥٬١٧٧ ل.س · ٣٦٫٩٨ $٥٬٥٩٧ ل.س−٨%

بيع منه ١٦٦ حول العالم
رضا المشترين ٩٧٫٧٪

اللون

المقاس

1 قطعة

أبرز المواصفاتعرض الكل ›

المنشأ🇨🇳 الصين

الوزن٠٫٥٤ كغ

الأبعاد15 × 10 × 3 سم

وزن الطرد٠٫٥٤ كغ

محميٌّ بزنبيل · حماية المشتري ٧ أيّام

حماية المشتري: إن وصلتك القطعة تالفةً أو مختلفةً عن الوصف أو لم تصل، نعيد لك المبلغ كاملاً. بلّغنا خلال ٧ أيام من الاستلام مع صورة.

ادفع بـ

الدفع عند الاستلام
شام كاش
بيميرا
بطاقة فيزا أو ماستركارد
شام كاش
بنك الشام

اسأل عن هذا المنتج على واتساب

معلومات المنتج

Features 【Optional Main Control Chip】 Uses 32-bit ARM Cortex-M4 series STM32F446ZET6 or STM32F407ZE main control chip. The two chips support Marlin and Klipper with high frequency. 【Strong DIY Support】 This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V. 【Motherboard Expansion Function】 Support BLTouch, locked-rotor detection, shut down after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional), dual Z-axis printer. 【TMC2209 Driver Features】 The TMC2209 stepper driver is not easy to lose steps and is in an ultra-quiet mode; the module has a large area of heat dissipation pad, which can reduce the temperature of the driver when it is working; the module supports three modes: STEP / DIR and UART. 【TMC2209 Driver Mode】 TMC Motor drivers can be used in SPI or UART mode by simply adjusting the onboard jumpers beneath each motor driver. Additionally, you can connect or disconnect the TMC DIAG pin using an onboard jumper allowing you to use hard end-stops or sensorless homing without the need to cut any pins. Note The chip firmware configuration of the new version of 407ZE is different, please see the instructions on github for details： https://github.com/bigtreetech/BIGTREETECH-OCTOPUS-V1.0/tree/master/Firmware STM32F407ZE can supports Marlin Klipper,but 512KB flash not enough & there is no customized version for RepRapFirmware. Usage of the PITFT50 and Octopus V1.1 motherboards:The PITFT50 touch screen and Octopus V1.1 motherboard need to be connected to the Raspberry Pi to be used normall Package list 1.Only the Octopus Board 2.Octopus Board with 8pcs TMC2208/TMC2208 UART/TMC2209/TMC2226/TMC5160T 3.Octopus Board with 8pcs TMC2209+MINI 12864 4.Octopus Board with 8pcs TMC2209+PI TFT50 5.Octopus Board with SFS V2.0 6.Octopus Board with Microprobe 7.Octopus Board with RJ11 to CAN Cable