Dental Wireless LED Curing Light 2200 mw/cm2 Highlight LV3 Curing Lamp Dental Resin Dentisty Equipment

Description: Name: Dental LED Curing Equipment Battery (rechargeable use): Lithium ion battery Battery capacity: 1600mAh Battery voltage: 3.7V Weight: about 400g with packaging Applicable temperature/humidity: 5°C~40°C/≤80% Packing specification: 300x150x60 mm Curing time:3s,5s,10s,15s,20s Charger input voltage: 100V-240VAC, 50-60HZ Output voltage: host dc 5v/1A LED light wavelength: 458.5nm Atmospheric pressure: 50kPa〜106kPa Light Intensity: P1 Highlight Mode 1800-2200mw/cm2 P2 Standard Model 1000-1300mw/cm2 Note: The time required for resin curing mainly depends on the resin brand, curing depth and area, etc., 3 seconds is a reference value, not an absolute value, respectfully. Use and safety precautions: 1. When using the machine for the first time, please charge it for at least 4 hours. The display scrolls when the battery is charging, and the display stops scrolling when it is fully charged. At this time, you can pull out the plug of the power adapter. Long-term charging is prohibited. 2. When in use, a disposable film cover should be inserted and repeated use is prohibited to prevent cross-infection. 3. In clinical use, the light source should be directly irradiated on the cured resin material to prevent improper irradiation position and affect the curing effect. 4. The original shading plate must be used to effectively prevent blue light from damaging the eyes. Blue light is strictly forbidden to irradiate the eyes. 5. Please use the original power adapter, other power adapters may cause damage to the lithium battery and control circuit. Operation method: 1. Lightly press the "M" mode setting button of the main unit, you can select any of the following two modes to enter the working state: (1) P1 high light intensity mode: 1800-2200mw/cm2 (2) P2 standard mode: 1000-1300mw/cm2 After selection, the display shows the corresponding characters (P1/P2). 2. Tap the "T" time setting button of the host to set the light curing time: (1) P1 mode can choose 3 or 5 seconds timing time (2) P2 mode can choose the timing time of 10, 15, 20 seconds 3. When in use, put the disposable film cover on the head of the main unit, then aim the light source at the position to be cured, press the "" on/off key, the main unit will emit a beep, the main unit will emit blue light and press the selected Working in working mode, the display screen starts to display the countdown time from the selected timing time, and ends at 0 o'clock, and the display screen returns to display the original set timing time. 4. During the work process, you can press the " on/off "to end the work at any time, and the display will return to the original set timing time. 5. After one irradiation cycle is over, you can immediately press the "on/off" key to start the next cycle. If it is obvious that the handle starts to get hot, stop working until the handle is completely cooled down before starting to work. In P2 mode, it is recommended that the continuous irradiation time does not exceed 120S. 6. Low-voltage indication: The host has a low-battery detection function. When a low battery is detected, the display flashes. Please charge it in time. 7. Connect the power adapter (optional) to the 100V-240V network power when charging, and insert the output end of the adapter into the charging port at the bottom of the host, and the display scrolls. 8. After use, please remove the disposable film cover from the head of the main unit and throw it into the trash can. Repeated use is prohibited. If the lens is stained with resin, please wipe it clean with cotton cloth to avoid affecting the light intensity. 9. The machine will automatically shut down after 2 minutes of inactivity, please press any key to turn it on. Features for Dental LED Curing Lamp 1. Wireless 2. USB 3. TWO working models: P1 Highlight Mode,P2 Standard Model 4. Time setting: P1:3, 5, P2:10, 15, 20s 5. Large capacity battery, A full charge can be used for more than 500times Packing: Host*1 Shading sheet*1 Date line*1 No charging stand

Ürün özellikleri